Rapid-air SERVO FEED / RAPID MASTER Manual do Utilizador descarregar pdf (Página 10)

10

programming procedure (continued)

Operator Input Terminal – Programming Procedure – Standard Software

MANUAL MODE F1=INCH

F2=SINGLE FEED MODE

F4=EXIT MANUAL MODE

CYCLE ROLL WITH KEYS

F2=SINGLE FEED

If the operator presses F2 then the

following screen is displayed. The

single feed mode is active and every

time the F1 key is pressed then the

feed will cycle and move the distance

indicated on the feed length line.

JOB#=00 FL=000.000

F1=FEED SINGLE LNGTH

F2=CUT F3=SINGLE CYC

F4=EXIT (SINGLE FEED)

Pressing F4 once resets the program

to the manual mode display. Pressing

the F4 key twice resets the program

to the main menu display. If the F4

key was pressed twice the following

screen is displayed.

MAIN SELECTION MENU

F1=JOB# F2=MANUAL

F3=AUTOMATIC CYCLE

F4=REVIEW JOB PROGRAM

F3=AUTOMATIC CYCLE

You can now select between batch or

continuous mode

SELECT CONTINUOUS OR

BATCH CYCLE F1=BATCH

F2=CONTINUOUS CYCLE

F4=EXIT TO MAIN MENU

F2=CONTINUOUS

If the F2 key was pressed then the

servo will be in the auto total mode

and the following screen appears.

AUTOMATIC TOT=000000

JOB#=00 CUT=O.150

FL=000.000 SPEED=100

ACCEL=OO1% F4=RETURN

Pressing the F4 key, stops the

automatic cycle and the main menu

screen appears.

MAIN SELECTION MENU

F1=JOB# F2=MANUAL

F3=AUTOMATIC CYCLE

F4=REVIEW JOB PROGRAM

F3=AUTOMATIC CYCLE

If the feed has been properly set up,

tested in manual, press electrically

interlocked with feed, feed and pilot

switches wired to the correct

terminals, then pressing the F3 key

will display the following screen.

SELECT CONTINUOUS OR

BATCH CYCLE F1=BATCH

F2=CONTINUOUS CYCLE

F4=EXIT TO MAIN MENU

F1 =BATCH

If the F1 key was pressed then the

servo will be in the auto batch mode

and the following screen appears.

BATCH SETTING=000000

BATCH COUNTER=000000

F1=RESET BATCH COUNT

F4=CONTINUE WITH COUNT

If F1 (reset batch count) is pressed

then the batch count will be reset

to its preset valve. If F4 (continue

with count) is pressed the batch

count will remain at its present

value. Either F1 or F4 will lead to the

following screen.

AUTOMATIC BATCH=000000

JOB#=XX CUT=0.XXX

FL=XXX.XXX SPEED=XXX%

ACCEL=XXX% F4=RETURN

Pressing the F4 key, stops the

automatic cycle and the main menu

screen appears.

When the automatic screen is

displayed, all keys except the F4 key

are inactive. Every time the press

cycles and trips the feed switch,

the feed will cycle once per the

parameters displayed on the screen.

If the feed encounters excessive

material drag while feeding or the

material being moved encounters

a restriction that stops the material

forward movement then a servo fault

can occur. If this happens then the

following screen is displayed.

DRIVE FAULT OCCURED

NOTE TYPE OF FAULT––

(xxx)

Example of fault – (2) = motor over

temperature.

Look up fault code printout listed in

this manual.

To reset the fault, the master on-off

switch has to be cycled which will

reset the controller. The material path

should be checked for obstruction and

parallelism to the die. If all this seems

to be satisfactory and another fault oc-

curs the factory should be consulted.

MAIN SELECTION MENU

F1=JOB# F2=MANUAL

F3=AUTOMATIC CYCLE

F4=REVIEW JOB PROGRAM

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 25 26

Comentários a estes Manuais

Sem comentários